Click

 

 

Nearly everybody has got their personal piece of advice when it comes to Installing A Bathtub.

Installing a tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a new one is also a reasonably difficult job. If the old bathtub is easily accessible, the job can relocate easily; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly help you mount a brand-new tub in your bathroom if you have actually already purchased a brand-new tub and do not require to alter the arrangement of your previous water system pipes.
Your devices as well as material list must comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Planning for the Setup

Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final setting.

 

 

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before moving on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Setting up the Bathtub

Making use of both wooden boards under its feet, place the bath tub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the tub till the spirit level reviews degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least once as this will resolve it right into its last placement.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Safeguard the faucet in position with the producer provided backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Tub

In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you like reading about How to Install a Bathtub? Try leaving a remark down the page. We would be delighted to listen to your views about this write-up. In hopes that you come back again in the future. Are you aware of somebody who is involved in How to Install a Bathtub? Take a moment to promote it. Kudos for your time. Come back soon.

Phone